Dodge Nitro Projector Headlamps

[rickaren]

Originally Posted by Frederick

Thanks for the write up and the advise about masking the prone areas with painter tape a very good idea.
I really need a pair of those headlights

That link comes back here?

Sorry for the confusion Frederick, but I created TWO Threads on Nitro Projector Headlamps on purpose.

ONE about these types of lights, how they look installed; four options available; warranty and price. Dodge Nitro Projector Headlamps (This Thread)

TWO is if are considering purchasing them or have, how to install them. http://www.dodge-nitro.com/forums/f1...eadlamps-4573/

I will edit both Threads to make this more clear. Thanks again for your comments.

Fredrick weather here in Indiana has not been the norm this year. I was in a hurry to take pictures the same night as my hurry-up install with snow in the forecast. I really didn't notice the grille was not properly installed until I noticed the right upper side had a gap and by correcting that it corrected headlamp alignment also. Usually Winter doesn't start so cold here, but I ended up installing a special ordered patio storm door(s) when the high temp was 14 degrees!

[Nitro north norway]

H.I.D Headlamp with halo bi xenon on ebay (...HELP...)

--------------------------------------------------------------------------------

Hi plz someone help me..

i bougth this from ebay.
2 SET HID 07+ DODGE NITRO CCFL HALO PROJECTOR HEADLIGHT - eBay (item 360299500559 end time Oct-10-10 13:08:49 PDT)
when ill contect them to the original harnest the ligts will only work peopertly when the car is not running.. but when ill start the car they only work for about 10 sec then they are flickering for a wile then they go off.
t
pls some one help me.. with som diagram how i chuld conect the cabels or so on..

im from Norway so my inglish writining is not so werry good

p.s
the firm ill bougth the hid lamps from send me digital ballasts but this do not work either..

My car is an Dodge Nitro SXT 4x4 2007 with europ version diesel 2.8 L 177 hp and 460 nm of tork.

If i install ballast from 35W to 50W then they work but not good a bit flickering in the rigth side..

my car comes with an H4 Socet with 55W/60W bulbs standard..

[mygti02]

correct me if im wrong guys, but i think he will need these ( http://www.ddmtuning.com/Products/Er...minator-3-PAIR ) to correct the issue right? dont all dodge car need the error code eliminator?

[rickaren]

Dear Nitro North Norway

I did not first respond since I thought you had added just the H.I.D. bulbs and not the whole headlamp assemblies as I did. Just replacing the bulbs has been an issue for some and did require some modifications to work. As far as adding the complete headlamp assemblies as I did they should be just plug-n-play. Same wiring harness and same plugs using the same switch! NO MODIFICATIONS ARE REQUIRED (at least on the Nitro USA vehicles).

It sounds like you may have a overload. If you unplug one lamp when in operation does this allow the other lamp to stay on and operate correctly?

[rickaren]

Dear Nitro North Norway

Your Lamps:

2 SET HID 07+ DODGE NITRO CCFL HALO PROJECTOR HEADLIGHT: eBay Motors (item 360299500559 end time Oct-10-10 13:08:49 PDT)


My Lamps:

JDM Black with LEDs and Clear Projector (CCFL) - 2007 Dodge Nitro Projector Headlights
low T-5 55W
T-3 ½ hi beam bulb 55W
Projector Headlights are completely DOT compliant.

In reviewing the two light sets they do look the same but look to use different bulbs and yours do not state they are DOT compliant. I suspect that may be the issue. Since they are guaranteed 1 year (mine 2) they need to correct or return as defective.

Will do some checking for you as to what you can do and will reply later.

[Nitro north norway]

Originally Posted by rickaren

Dear Nitro North Norway

I did not first respond since I thought you had added just the H.I.D. bulbs and not the whole headlamp assemblies as I did. Just replacing the bulbs has been an issue for some and did require some modifications to work. As far as adding the complete headlamp assemblies as I did they should be just plug-n-play. Same wiring harness and same plugs using the same switch! NO MODIFICATIONS ARE REQUIRED (at least on the Nitro USA vehicles).

It sounds like you may have a overload. If you unplug one lamp when in operation does this allow the other lamp to stay on and operate correctly?

Nope its the same shi.... but went to an electric ekspert and hi told me that my car have canbus system in it.. The scope he used was sending an heart beat rytem pulsing look alike power to the headlamps.. it ppeked under 9 volts.. upp to 14.75 volts ...

[rickaren]

So did he fix the problem?

[Nitro north norway]

Originally Posted by rickaren

Dear Nitro North Norway

Your Lamps:

2 SET HID 07+ DODGE NITRO CCFL HALO PROJECTOR HEADLIGHT: eBay Motors (item 360299500559 end time Oct-10-10 13:08:49 PDT)


My Lamps:

JDM Black with LEDs and Clear Projector (CCFL) - 2007 Dodge Nitro Projector Headlights
low T-5 55W
T-3 ½ hi beam bulb 55W
Projector Headlights are completely DOT compliant.

In reviewing the two light sets they do look the same but look to use different bulbs and yours do not state they are DOT compliant. I suspect that may be the issue. Since they are guaranteed 1 year (mine 2) they need to correct or return as defective.

Will do some checking for you as to what you can do and will reply later.

Hi and thx.. soo far

My Headlights are completely DOT compliant it is writen in the glass..
but i got the H.I.D thats not working rigth.. the Halo Rings works fine all the time..

but when i change the H.I.D Ballasts to 50 W the are working all the time. And my dealer in town sayes the lightening module will brake down if ill use this for a period time..

[Nitro north norway]

Originally Posted by rickaren

So did he fix the problem?

Nope..

he must think what a h.. he can do.. to fix the prob..

mine kit came with 35W h.i.d ballast digital ones.. but not working..

[mygti02]

does he need the e-code eliminator maybe?