Dodge Nitro Forum banner

1 - 5 of 5 Posts

·
Super Moderator
Joined
·
23,330 Posts
Discussion Starter #1

Sep 22, 2010

I will give a detailed tour of my parents Dodge Nitro
 

·
Super Moderator
Joined
·
23,330 Posts
Discussion Starter #2

Dec 1, 2010

Going up the road, turning round and attempting to park it
 

·
Super Moderator
Joined
·
23,330 Posts
Discussion Starter #3

Feb 27, 2010

Located in downtown Providence Rhode Island, the Rhode Island School of Design has a fully staffed public safety department that is responsible for the safety and well being of all people utilizing the RISD facilities. This new Dodge Nitro will join their current fleet of Ford Explorers and Ford Escapes.

This installation utlilized the following equipment:

Motorola XTL2500 800 Mhz Trunking Radio
EVM-IDM308VS Ignition Delay Module
SoundOff Signal ETULT37W 3" by 7" White LED Dome Light
SoundOff Signal ECVDMLT2ALØØ White/Red LED Dome Light
SoundOff Signal ETSA38ØR Remote Siren and light controller
SoundOff Signal ETSS1ØØH 100 Watt Siren Speaker
This Installation utilized the following SoundOff Signal warning lights:

EPL9048 Pinnacle Light Bar with LED Takedowns and LED Alley Lights
Two LED3s, color Red, one on each front fender
Two Single Split Ghosts, color Red/White, mounted in the grille
One ETHFSS-SP-ISO Isolated headlight flasher
One ELUCKVØ2D Four Head LED Undercover Kit
One EL3HØ8AØØR UltraLite Interior Warning bar, color Red
 

·
Super Moderator
Joined
·
23,330 Posts
Discussion Starter #4

May 4, 2011

Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" Draw-Tite Trailer Hitch 75517

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Today on this 2010 Dodge Nitro we are going to install part number 75517 from Draw-Tite. This will also apply to part number 87426 from Hidden Hitch. This is what the hitch looks like when it is on the vehicle. Now we will go ahead and give you a couple of measurements that will help you out in ing accessories for it, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be 17-1/2 inches on this particular vehicle. And from the center of the hitch pin hole to the outside edge of the bumper is going to be 2 inches. Next we will show you how it gets installed. 0:34




May 5, 2011

http://www.etrailer.com/Brake-Controller/Tekonsha/90885.html

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Today on this 2010 Dodge Nitro we are going to install brake controller part number 90885 from Tekonsha. This is their Prodigy P2 brake controller. And to install this, we are going to use part number ETBC7. The first thing we need to do is go ahead and take the bracket from the ETBC7 kit. We are going to install that on to the bracket that is on the hitch. The next step is to go ahead and do some partial assembly on the 7-pole itself. What we will do is we will go ahead and add the gray cable that comes with the kit and we will hook it up to our 7-pole connector. What we are going to do is actually just wind this up in electric tape and leave our leads out that we need. We are going to leave our 4-pole sticking out and we are going to need our brake wire which is going to be blue and out black wire for 12 volt power supply. And then we will just wrap up our purple and white wires. Our white wire is going to go directly to the frame for ground. And then the purple wire is going to be for reverse lights if it is ever needed. And to our black and blue wires we are going to install the grey cable that has the black and white wires inside of it. What we are going to do is just peel away the grey sheath. Then stripe our wires back and make our connections: black to black and white to blue. Cover those up with some electric tape. Next we will go ahead and install the loom along the wires like this. 1:20



May 5, 2011

http://www.etrailer.com/p-118455.html

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Today on this 2010 Dodge Nitro we are going to install part number 118455 from Tow Ready. This is our T-One wiring harness. This T-One wiring harness does mount behind the tail lights on both sides of the vehicle. Also, there is a lead that will be run up to the battery for our 12 volt power supply. We will open the hatch and remove the tail lights. The lights are held on by the plastic rivets here and here. We are going to use a screw driver and pry the rivets out a little bit. Then we will use a trim tool and pull out the rivet. Pull straight back on it to release it. Then disconnect the light from the harness by pushing down on this tab right here. Go ahead and repeat for the other side. 0:45
 

·
Super Moderator
Joined
·
23,330 Posts
Discussion Starter #5

May 6, 2011

Purchase this filter at: FilterHeads.com - Part Number AQ1131

AQ1131
This filter fits Dodge Nitro 07-10 and Jeep Liberty 08-10. The model shown in this video is a 2010 Dodge Nitro, but installation is similar on the other models.
 
1 - 5 of 5 Posts
Top